The Amp Garage

I'm just playing with my panel layout options in Paint based on the actual front and back panels and what sorts of holes they have.
I'm not sure, but maybe something like this: I want to build it without relays first, but I do want to make it possible to add OD and PAB relays later...

Not sure if I'd ever need to switch it in or out mid-song, great question to consider if it's worth putting on a pedal. The relay was used primarily to keep the wire runs shorter. My goal was to keep it as close to 102 as possible when the Dumbleator was not in use. The possibility of putting it on...

I've used the dumbleator in both my Skyliner and the Delta amps I've documented here. The cap values are a little different than standard for modified filtering but the basics are very similar. They don't have relay switching but that can be easily designed in. Check out the Delta (183) for the mat...

bcmatt I did a very similar build, if I were to put together a schematic of my build it would look nearly identical to what you pieced together. On mine the switch to select or bypass the Dumbleator is actually a relay. I did this mainly to avoid long signal wire runs to a switch. Where I was able ...

FUCHSAUDIO wrote: ↑Tue May 07, 2024 4:31 pm No reason you can't. I would add a 100 ohm series gate resistor on each, and also keep the 10 ohm source resistors on each, the input drain leads can simply tie to the same point.

So, like this?

I'd like to convert another Traynor YGL-3a that I have to a #102 High-Plate Skyliner. It's already been modded a bit to take a couple KT88s. This is it currently: 20240504_140745.jpg YGL with KT88 screen VVR.jpg I'm first trying to theorize what a built-in Dumbleator in a #102 would look like and I ...

So, this is the regular VVR I use in Cathode biased amps: VVR.jpg If power handling is a worry and I'm worried about that MosFET, can I just add a second MosFET in parallel? Like this?: Parallel MosFET VVR.jpg Do MosFETs work like that, or does that screw up the circuit? I imagine that the heat diss...

Pretty similar to ODS. A branch from B+2 before the VVR could be used to supply the D'lator... I guess that's what you're thinking, and that's a proven approach. Since I'm not really sure what model I should use for a 2x KT88 ODS power section. I'll start by making a schematic with the current powe...

Since this is going to be some sort of ODS conversion, I think it would be appropriate that I start a thread with my plan in the Dumble Discussion. This is beginning to become the wrong section for such talk.

Just looking at the actual power section of this YGL:

I want to forget about adding reverb for now... but am still obsessing about trying to build in a Dumbleator. I am maybe redoing someone's work, but I haven't found it exactly... so I messed around with Paint to theorize how one would add a dumbleator to a 102 circuit: 102 with Dumbleator Theorized....

Since KT8K8 are beam tubes like 6L6, and the power amp is a clean Hi-Fi type, I don't think it would matter. That's what I figured. Mostly it's something like the 183 or HRM that get a little different. I'm getting a little mixed up keeping track of all the different models and trying to hear the d...

I'm becoming quite happy with my other YGL-3a that was completely gutted and converted to an SSS... I'm feeling like this YGL-3a finally deserves a proper conversion to an ODS circuit. I'm thinking I'd like to keep it running these 2 KT-88s. It seems to be working well, with this VVR for the screen ...

I just installed a slightly less comical looking 20k 5 watt dropping resister instead of these 2 in series. I'm looking forward to running this all through its paces in a variety of settings to see if it's hype-worthy yet.

In the diagram the switch is set to fast ( higher gain) mode. https://ampgarage.com/forum/files/Express_pre_amp_variation.jpg OK, thanks. So I guess since I'm wired to the plate load being split, I'm in the lower gain mode as far as the plate is concerned. But mine's not that circuit otherwise, bec...